凤楼网站怎么做的网站设计与制作毕业论文范文

一、开机阶段

开机有如下阶段。抛开开机动画需要的audio、surfaceflinger等进程，大部分android程序是在/data分区加载完整以后开始加载。所以cpuset的配置可以在 post-fs-data之后。注意，init.rc的不同阶段脚本都可能覆盖前面配置的cpuset。配置好检查与预期不一致，则要配置被重置了。

1) early-init
 
a) wait_for_coldboot_done
 
b) property_init
 
c) keychord_int
 
d) console_init
 
e) set_init_properties
 
2) init
 
3) early-fs
 
4) fs
 
5) post-fs
 
6) post-fs-data
 
f) property_service_init
 
g) signal_init
 
h) check_startup
 
7) early-boot
 
8) boot
 
9) service
 

二、配置cpuset

本例策略如下：
开机阶段：
write /dev/cpuset/top-app/cpus 0-5
write /dev/cpuset/foreground/cpus 0-5
write /dev/cpuset/system-background/cpus 0-5
write /dev/cpuset/background/cpus 4-5

开机完成后：
write /dev/cpuset/top-app/cpus 0-3
write /dev/cpuset/foreground/cpus 0-3
write /dev/cpuset/system-background/cpus 3-5

配置方法：

修改init.rc

on early-bootwrite /dev/cpuset/top-app/cpus 0-5write /dev/cpuset/foreground/cpus 0-5write /dev/cpuset/foreground/boost/cpus 0-5write /dev/cpuset/system-background/cpus 0-5write /dev/cpuset/background/cpus 4-5

....

on property:sys.boot_completed=1write /proc/sys/kernel/printk 4# init.vendor.rc can override below at on property:sys.boot_completed if neededwrite /dev/cpuset/top-app/cpus 0-3write /dev/cpuset/foreground/cpus 0-3write /dev/cpuset/system-background/cpus 3-5

三、配置特定进程的cpuset

# We want all cores for cameramkdir /dev/cpuset/camera-daemonwrite /dev/cpuset/camera-daemon/cpus 0-5write /dev/cpuset/camera-daemon/mems 0chown cameraserver cameraserver /dev/cpuset/camera-daemonchown cameraserver cameraserver /dev/cpuset/camera-daemon/taskschmod 0660 /dev/cpuset/camera-daemon/tasks

四、验证方法：

在adb shell里面：

#cd /dev/cpuset/top-app
/dev/cpuset/top-app # ps -A -p `cat tasks`

可以看到top-app下活跃的进程

USER           PID  PPID     VSZ    RSS WCHAN            ADDR S NAME
u0_a53        2217   378 4546160 192796 ep_poll             0 S com.fiilll.app.launcher

然后敲：

ps -o pid,psr,comm -p `pidof com.gwm.fiill.launcher`

 显示的PSR就是核

  PID PSR COMM2217   1 app_process64

同样的步骤查看system-background

/dev/cpuset/system-background # ps -A -p `cat tasks`
USER           PID  PPID     VSZ    RSS WCHAN            ADDR S NAME
logd           329     1   76160  56700 sigsuspend          0 S logd
system         330     1   11156   3728 binder_ioctl_write_read 0 S servicemanager
system         331     1 2126696   6756 binder_ioctl_write_read 0 S hwservicemanager
system         332     1   11872   3096 binder_ioctl_write_read 0 S vndservicemanager
system         474     1   56072  17740 binder_ioctl_write_read 0 S android.hardware.graphics.composer@2.2-service
root           729     1    9544   2400 ep_poll             0 S lmkd
system         731     1 2192692  34460 ep_poll             0 S surfaceflinger
system         735     1   11220   4420 poll_schedule_timeout 0 S name-server
statsd         897     1   23296   6648 ep_poll             0 S statsd
root           898     1   22688   5752 binder_ioctl_write_read 0 S storaged
root           906     1   38444  13552 poll_schedule_timeout 0 S dlt-daemon
system         954     1 2128968   7096 binder_ioctl_write_read 0 S gatekeeperd
root           955     1   18988   4752 binder_ioctl_write_read 0 S perfprofd
tombstoned     959     1    9232   2300 ep_poll             0 S tombstoned

由于statsd是开机完成前加载的，所以第一次cpuset可能在0-5之间

  PID PSR COMM897   0 statsd

我们以此可以判断开机时候配置的是否正常。

现在杀掉该进程重新加载：

kill -6 `pidof statsd`

再查看它的cpuset：

ps -o pid,psr,comm -p `pidof statsd`

发现cpuset已经变了

  PID PSR COMM9766   3 statsd